Calculator
State solar incentive calculator
Pick a state and the calculator loads its tax credit, rebate, export rule, electricity price and sunlight. Change anything to match your own quote and utility.
Checked against primary sources on . State data from this site; method below
What it does
The calculator estimates the finances of a solar system that you buy and own. It starts from the data on each state page and from three national datasets, applies them to the system you describe, and shows every line of the result.
It asks for no contact details and sends nothing to a server. The arithmetic runs in your browser, and the same code is published for anyone to inspect.
The inputs
System size. In kilowatts of panel capacity. The system size calculator works this out from your electricity use.
Installed price. Dollars per watt before incentives. The default is the median for your state where Lawrence Berkeley National Laboratory reports one, and the national median of $3.60 otherwise. A quote divided by system size in watts gives your own figure.
Electricity price. The state's average residential price from the Energy Information Administration for 2025. Your own rate may be well above or below it. Use the per-kilowatt-hour total from a recent bill, excluding fixed monthly charges.
Solar used in the home. The share of the system's output that you consume as it is generated. Without a battery this is typically 30% to 50%. The default is 50%.
Export credit. What an exported kilowatt-hour earns, as a percentage of the retail price. It is prefilled from the state's rule: 100% for full net metering, a lower figure where exports are credited below retail, and 0% where no statewide rule guarantees anything. If your utility pays a specific rate, divide it by your retail rate and enter the result.
Under "More inputs" you can change production per kilowatt, every state incentive, and the assumptions about electricity price growth and panel degradation.
The method
- Installed price = size in watts × price per watt.
- Rebate = size × per-watt rebate, plus any flat rebate, up to the cap.
- State tax credit = (price − rebate) × credit percentage, up to the cap, plus any flat credit.
- Net cost = price − rebate − credit. No federal credit is applied, because the residential credit ended for installations after 31 December 2025.
- Year-one production = size × production per kilowatt.
- Year-one value = (production × self-use share × retail price) + (production × exported share × retail price × export credit) + SREC income + performance payments.
- Later years repeat step 6 with output reduced by the degradation rate and the electricity price raised by the escalation rate. SREC and performance payments stop at the end of their term.
- Payback is the point at which cumulative value reaches net cost.
What it leaves out
- Loan interest. Use the loan calculator alongside it.
- Utility and city incentives unless most of the state can get them. Add yours under "Flat rebate".
- Fixed charges, minimum bills and demand charges that apply to solar customers in some territories.
- Time-of-use rates. The model uses one average price for all hours.
- Maintenance and inverter replacement.
- Property tax savings from an exemption, which depend on local assessment.
- Income tax on SREC or performance payments.
- Batteries. To see their effect on export value, use the net metering calculator.
The result is an estimate for comparing options and for checking a quote. It is not a prediction of your bill.
Why does the calculator show no federal tax credit?
Because a homeowner who buys a system installed after 31 December 2025 does not receive one. The Residential Clean Energy Credit ended on that date.
Where do the state incentive figures come from?
From the programs recorded on each state page, which link to the statutes, agency pages and tariffs they are drawn from. Only incentives open to most households in the state are loaded by default.
Why is the export credit zero for my state?
Your state has no statewide rule guaranteeing a credit for exported power, so the calculator cannot assume one. Many utilities in those states do pay something. Enter your utility's export rate as a percentage of your retail rate.
How accurate is the production figure?
It is a modeled value for a south-facing array at a 20 degree tilt in your state's largest city. A different location, orientation or shading will change it. An installer's site-specific estimate is better.
Related
- Net metering and net billing calculatorThe yearly value of exported power under different credit rates, with and without a battery.
- SREC income calculatorCertificates earned per year and income over the eligibility term.
- Solar system size calculatorThe array size and panel count that covers your electricity use.
- Solar loan calculatorMonthly payment against monthly savings, including dealer fees.